how to powder coat a yeti cup This is a topic that many people are looking for. khurak.net is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, khurak.net would like to introduce to you How to DIY Powder Coat a Yeti Cup!. Following along are instructions in the video below:
To man crafting today. Were going to go through all the steps it takes takes to powdercoat a stainless steel tumbler such as a yeti and arctic and sever the brands that are out there on the market today first you want to make sure you have great lighting. I cant impress upon you how important good lighting is to good powder coating next you need a place to do your powder coating in this video.
Were using a simple cardboard box. And it does everything we need for this particular purpose the next thing youll need is a powder coating gun of some sort here were using a decent entry level gun made by eastwood this happens to be their dual voltage powder coating system and we found that it works really well for our purposes the red button. You see there allows you to switch between 15 and 25 kilovolts now youre looking at the alligator clip.
Which allows you to ground your piece and this switch allows you to complete the circuit next youll need an air compressor of some sort once inside the powder coating booth youll see that ive made a cut out and included a 20 by 20 air filter to filter out the powder coating as im applying it at the rear of the booth behind the filter. We have a simple 20 by 20 box fan and for cleanup.
We have a shop vac and on the outside of the house for blowing off the gun. We have a second air compressor inside. Were just using a simple pancake compressor because it only requires 8 psi to apply the powder through the powder coat gun the first step in preparing the powder coat is making sure your part is as clean as possible here.
Were using lint free rags and acetone to remove any glues or sharpie marker marks that weve used to line up our artwork prior to powder coating here. Were about to put our part on a cookie sheet. Thats covered in aluminum foil with a piece of flashing on top and the flashing will be thrown away the foil will be thrown away and our cookie sheet should have minimal amounts of powder coating on it the last thing we do before the actual powder coating were going to burn off any possible lint that may still be on the cup and now we start.
The powder coating process. Again.
The gun is set at about 8 psi. And the key here is to make sure youre putting on enough powder in our initial applications. We were found that we were going a little thin.
And that didnt give us the best results. So you almost have to put it on heavier than you think you need to put it on down near the bottom of the cup as youre doing your application make sure you really pay close attention to how heavy its going on is real easy to under applied at that bottom edge because of whats called the faraday effect. It just doesnt want to apply that easily to that lower part so pay close attention and make sure you get a good even amount of coverage in that area make sure you follow the manufacturers recommendations for the specific powder that youre using temperatures can vary from powder powder.
Now were ready to put our cup into the oven. Where were going to let it bake for 10 minutes.
Until the powder flows at which point. Well readjust the temperature. And let it cure for 10 minutes in the meantime.
Were going to clean up using the shopvac powder coating powder is extremely easy to clean up this is nothing like cleanup of a paint booth okay and now you can see the powder is flowed and were going to readjust our temperature and let it cure for another ten minutes if you look on the label of any of your powder coating powders youll see the temperatures that are recommended okay heres time for the big reveal our alarm went off turn off the oven. Unless youre about to do another. Part and now were going to pull the part out and we get to see just how well our powder coating process took also notice that we removed the cup.
Almost immediately from the flashing and heres a close up you can notice that the etched areas are actually darker under the translucent powder coating. I think it gives a really fantastic look and now its time to take a photo and this is our little photo area where we take pictures for our facebook. Page and for our customers.
So they can see it even before theyve had a chance to get their hands on it thanks for watching our video. We hope you found it helpful have a great day you .
Thank you for watching all the articles on the topic How to DIY Powder Coat a Yeti Cup!. All shares of khurak.net are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.