tabletop charging station This is a topic that many people are looking for. khurak.net is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, khurak.net would like to introduce to you How to Build a Tablet Charging Station. Following along are instructions in the video below:
“There and welcome in to shop fix a community joined together for the love of of woodworking. My name is william andrea and in today s episode. I m really to show you guys this custom tablet. Charging station with built in power.
Now this charging station can hold up to 8 tablets with or without their cases. So let s get right into this and see how it s built hey. Everyone i hope you re really excited for this week s episode of shop fix if you want to give me a my channel support don t forget to subscribe and hit that like button. Now.
Let s get right into this let s start this tablet. Charging station. Build with four two by fours and let s head over to the jointer to start milling these two by fours up after face joining let s begin to edge joint. These boards.
So we can head over to the table saw as of recording this video. My planer was actually out of commission. Because i needed to change out the blades so if you find yourself in the same predicament. Because you don t own a planer you can use this technique to mill up your boards.
Anytime you want now let s take these forwards over to the miter saw to get one edge square. Then we ll measure and make a stop at 12 inches and make our final cross. Cuts we want the shelves to be 15 inches apart. So that every tablet could be in a case and still be put into the slot after measuring out every 15 inches.
We re gonna mark that and then clamp the board s together or you can do as i did and tape them up really well and go ahead and take it to the table. Saw and use a crosscut sled or a simple one that i have right here start cutting them out now. After you re done cutting out the slots make sure that you have each measurement correct. And the shelf will fit in before you untape it or unclamp.
The boards now for our shells. We re going to use 8 inch material. And that s exactly what we cut out of those two by fours now you can use any material. You like i just found that the handy.
Bore panel is very cost effective and it looks nice because it has the darker color now for side panels. We re just gonna simply cut out a groove here on the table saw so that we can slide in a quarter inch plywood panel you could see me here cutting out the width on the table saw let s go ahead and take that to the miter saw to get a rough cut length. Now its be able to embed a surge protector and have the cord run out. We re gonna have to create a little opening right here at the bottom of the 2×4 alternatively.
You could put this opening and the quarter inch side panel. Which would give you more flexibility in case you need to remove the surge protector now after we ve got that cut out we can drill. Some pilot holes mount some screws and attach our search protector now let s move on and cut out the back panel. Now this back panel is gonna have to have the same notch cut out just as we did the 2×4 well now it s time to assemble some of these pieces together you could see me here adding some glue to the back panel and attaching the 2×4 shelf.
Support. Now we need to add glue to the notches. We made in the 2×4. So that we can glue our shelves in place.
I want to thank you for tuning in to this episode of shop fix if you ve enjoyed this content. So far don t forget to hit that like button. Now let s continue by adding on the search protector before the final assembly. You ll want to test out your surge protector with all the power blocks and the cables that you re gonna use to make sure that doesn t get too hot.
If it gets too hot. You ll have to add a fan or some kind of exhaust to make sure that it cools down now to complete this assembly we need to create some decorative edges for the front of the tablet. Charging station. These decorative edges will cover up the grooves at the front of the case and allow us to securely attach the front shelf.
Supports. I happen to have this piece of oak laying around the shop you can certainly modify it if you wish the main thing here is just to make sure that your board lays about a quarter inch to a half inch over the edge and once they re dry you can go ahead and take them and gloom on the front of your case. After securely mounting them you can take a square and line. It up on the edge and move it up and down side to side to get it perfectly even then move on to the next side and repeat that same process.
My recommendation for this step of the assembly is to make sure that when you add the glue to the slots that you don t overfill them because when you squeeze them onto the shelves. It s gonna seep out and if you put too much it s gonna be really hard to get in there with a q. Tip or a rag or anything to wipe it up so make sure that you don t over apply the glue at this assembly step after it s all done drying you can use your preferred tool to make sure all the ends are square with one another now. It s time to start creating the base for this tablet.
Charging station. I happen to use half inch mdf because i had an extra sheet laying around. But you can certainly use pine to match your two by fours you ll definitely want to add a decorative edge this base piece. I happen to use a router table to get this job done at this point in the project.
I was really excited to test fit everything and see how this thing s coming together. Now let s use the same steps as we did the base panel to get the top panel all ready to go after watching up to this point of the video. If you have any suggestions to make this tablet. Charging station.
Even better feel free to comment below to make it easier to access all of the electrical components within this tablet. Charging station. We re gonna make the top panel completely removable now after completing the base panel on the top panel. This design is really starting to take shape to securely and accurately attach the two by fours to the mdf base panel.
We re first gonna apply a thin amount of glue and then attach that to the base panel. Let that dry then flip the whole thing over mark measure and drive in some screws. I ve created the shop fix channel with the intent of being very thorough and detailed when explaining project designs. Reviewing tools and giving any woodworking advice from my past experiences.
If you find this amount of detail helpful let me know if or if not in the comment section below. Thank. You well after all those detail cuts now we re getting somewhere let s go ahead and test fit those quarter inch side panels. Now we can go ahead and mark that side panel for its final cross cut make sure to hit this mark dead on because there s no wiggle room.
It s got to be flush well now that we have all our pieces. Assembled we can go ahead and sand this to a nice smooth finish here s a quick glimpse of what the tablet. Charging station. Looks like with all the power blocks plugged.
In and the cables routed to each of the shelves. And here s a look at the back panel. After having full access to all the electrical components within this tablet. Charging station.
Look how fast. It is to assemble it all back together. Let s go ahead and hit this case for the tack cloth. So we can go ahead and stain it for this tablet.
Charging station. I happen to use men waxes early american to match the oak in the front overall. I had a lot of fun using leftover materials around my shop to create this custom tablet. Charging station with built in power.
It makes me wonder what other bills. I m missing out on if you have any ideas for my future projects. Let me know in the comment section below. Now that we ve got this charging station all stained these tablets are about to meet their new home if you ve enjoyed this build and wonder what other projects.
I ve designed head over to my shop fix channel page to see more project videos. I want to thank you for your support for the shop fix channel and i value any suggestions or comments you may have i am very eager to hear from the shop fix community. But until next time have ” ..
Thank you for watching all the articles on the topic How to Build a Tablet Charging Station. All shares of khurak.net are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.