replace pixel battery This is a topic that many people are looking for. khurak.net is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, khurak.net would like to introduce to you Google Pixel Teardown – Screen Repair Battery Replacement Fix. Following along are instructions in the video below:
“We are going to find out what is inside na pixel. The latest android phone phone from google ill show a screen replacement. How to swap nthe battery. And even to take out the charging port lets get started intro.
While this phone is glued shut. The screen nreplacement is surprisingly easy. Especially if you don t care about your original nscreen anymore. I m using heat to soften the adhesive around nthe inside edges then using a very thin metal pry tool to slide nbetween the glass and the metal frame of the phone.
A good rule of thumb is to just not plan non your screen surviving this process. But if all you need to do is replace a battery. Nor something and want to keep your screen make sure the metal does not touch the black npart of the screen under the glass. The black part is the display or led the top glass of the screen can handle some nabuse.
But the led underneath is like a potato chip and will crack and crumble if you even nlook at it the wrong way you ll see the ribbon cables to avoid here nin a second as well they have the strength of paper. So try not to rip them either. I m heating up the screen about every 20 to n30 seconds. Keeping the glass barely too hot to touch this keeps the adhesive that holds the glass nto.
The frame soft and pliable each time. I stick my tool under the glass ni keep it away from the display underneath after removing the adhesive. All the way around nthe frame the screen lifts off exposing one long ribbon cable. I tested my screen at this point to see if ni was successful during the removal process.
Luckily i was able to remove the screen in none piece..
I turned the phone off again. And then loosened up the two t5 screws. Holding nthe silver bracket in place over the ribbon cable connection. Then using a plastic pry tool.
I can unsnap nthe display from the phone just like a little lego and this is the entire display. The glass layer and the led layer make up nthe screen look how thin. It is i will link the replacement screens in the nvideo description right below this video. I imagine they will come with a preinstalled nadhesive making the installation fairly easy if all you came for was the screen repair njust plop.
The new one back on and you are good to go. I m going to continue delving deeper into ninto this device. There are 9. More t5 screws around the mid plate.
And it s always good practice to keep your nscrews organized even if they all appear to be the same size put the screws back in the hole. They came nfrom the midframe has a little gap at the bottom nperfect for a little pry tool. There is no more adhesive under this frame. Nit is just wedged into the metal of the phone after the clasps are released the midframe nfolds up with one more little ribbon cable at the top for the earpiece holding it to nthe phone body ill unclip that and set it off to the side and unplug the battery this helps keep anything else from frying nas.
I m working on the phone. There is a long extension ribbon cable going nfrom the main board to the charging port. The tape is shaped a little bit different non each of the ends. It is imperative that this gets connected back oriented.
The same ndirection..
It started in so stay organized and remember how it looks nbefore you take it off it looks like the battery has a long strip nright down the middle that can be turned into a pull tab rip. The battery and pull it out. But since i am going to reuse my battery nill pop it out the old fashion way with a little bit of leverage do not puncture. This battery or it will start non fire.
Watch my note. 7. Battery exploding video for nthat visual. As always replacement batteries for this nphone will be linked in the video description right below this video.
It is fun that the aluminum frame of this nphone is as blue on the inside as it is on the outside it really is really blue. There is one t5 screw holding down the usb nc charging port into place. The vibrator motor comes out with it make sure to detach the 2 round signal wires nfrom the bottom as well here is the charging port. If you are replacing nyour charging port and your new one doesn not come with the rubber microphone housing nor vibrator make sure to transfer those components over to your new port this is the loud speaker it gets its signal from the little two golden nrectangle contact pads.
There at the edge. It is held in place by that same metallic ntape you see in other places on this phone moving up around the motherboard. It has two nt5 screws holding. It to the frame and a two more of those round signal wires.
Ill unclip. The power and volume ribbon cable nand pop out the sim card trey which i should have done before opening the phone earlier. But its ok because on this sim card trey nwe find a little easter egg. This includes the address of google headquarters kinda fun after that sim card trey is out the motherboard ncan be lifted up this.
Part is only useful..
If you are going nto be replacing your fingerprint scanner. Which is plugged in with the same lego like nconnection as everything else as we saw from my durability test video. The nscanner is pretty durable. But nothing is invincible and someday might need replacing the scanner can be pushed into the phone from nthe outside.
Now here is the back glass panel. Which can probably be removed using the same nheating method that we used with the front glass. I m wondering if the curved edge of this glass nis refracting light into the camera unit contributing to the halo effect. Some people are seeing non their camera pictures here is the motherboard.
The copper tape is probably there to help nheat dissipation ill be removing the front and rear cameras. Both are plugged in with the little lego connections. This close up of the camera lenses show that nneither of them are using any hardware stabilization or ois. Only electronic stabilization is being used nwith this phone.
Which isn t always my favorite. The htc 10. Had ois or hardware stabilization non both the front and rear cameras. Ill have to do a camera test of my own on nthis pixel to get a better opinion.
The cameras clip back into place. Easy. Enough just line up the little connector and you ll nfeel. It snap in right there next to the beautiful and always useful and very much appreciated nheadphone jack make sure you are plugging the fingerprint nscanner into the non copper colored side of the motherboard and when you put the motherboard into place nmake sure nothing is trapped underneath like the power button ribbon or the two round nsignal wires.
The loud speaker drops into place and then nill plug the signal wires into the bottom of the charging port and set the charging nport into place inside the frame next to the little vibrator..
There is one screw on the charging port and ntwo more screws on the motherboard that need to be tightened ill set the battery into place. But i m not going to plug it in just yet before that happens ill take care of the nextension ribbon cable. Making sure that it is oriented in the correct ndirection look at the shape of the tape on the ends. The phone will not function.
If you plug this nin backwards ask me how i know after the extension ribbon the power ribbon nbattery ribbon and the midplate earpiece ribbon are connected take that midframe and tuck nthe top end into the phone first before pressing down the sides. Then use nine t5 screws to hold that down and then we can test out our new screen make sure it functions before finishing the ninstallation. The screen is plugged into place get the nlittle silver metal bracket over the top with its two screws and it looks like everything nis functioning. So far.
The new screen will sit flush with the outer nedge of the phone. I m just reinstalling my old screen so its nnot looking as pretty. But the new screens will look much better. I m most active on twitter and instagram.
So if you want to see my future projects nand behind the scenes head over there. And if you enjoyed this video or it helped you nlet me know in the comments and hit that subscribe button. I always appreciate it thanks a ton for watching. ” .
Thank you for watching all the articles on the topic Google Pixel Teardown – Screen Repair Battery Replacement Fix. All shares of khurak.net are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.